Ashly amplifiers for hospitality run the gamut from TM Series, which is sufficient for the simple needs of mom & pop retail stores and restaurants, where just a few speakers are used for background music and paging. From there, it steps up to nX and nXp which provide increased power with multi-mode power for a mix of 8 Ohm and 70V speakers if necessary and DSP for system processing all in one unit. Then, to ne, which offers up to 8 channels of power & DSP to handle multi-zone requirements of sports bars and big-box retail. Protea -equipped modes will give you all the processing for making background music sound great, ducking for priority override of source (including paging) and remote option. Lastly, Ashly offers the widest selection of 70V and Dante-equipped power amplifiers in the industry, so we’re sure to have just the right amplifier solution for your needs.

Schools represent a multi-faceted environment with various needs. School gyms and auditoriums typically require high-power, input count and challenging acoustics. Protea-equipped nXp can offer power, flexibility and functionality for even the largest speaker compliment and with DSP horsepower to take care of matrix -mixing, speaker system management duties. pema offers a “system-in-a-box” approach with up to 8 x 250W, mic inputs with matrix DSP mixing and more. KLR is a cost-effective powerhouse series for use with separate mixers and DSP components and is ideal for sports fields and gymnasiums. KLR provides high-performance bang-for-the-buck.

Sound systems for sports facilities often demand flexibility and dependability. Day to day operation (long hours, outdoor conditions, etc.…) can place stresses that pushes amplifier performance to the edge. No worries. Ashly amps are designed to go to the edge and beyond. Our advanced Class D designs are highly energy efficient, which means they are very cool running and far less prone to failure than many similar amps. Ashly’s Dynamic PFC (Power-factor correction) means more intelligent handling of current and less thermal drift, while advanced Power Management allows the amps to work only when they need to, utilizing less current and keeping operating temperature at minimum. The nX Series can drive any load for mix and match system configurations (like 8 Ohm, full-range speakers for the hockey rink and 70V distributed speakers for the peripheral areas), each with it’s own independent DSP settings (nXp). For larger, more spread-out facilities where multi-zone FGM and paging are required, ne and pema Series can provide up to 8 x 250W at 4/8 Ohms or 70V. Dante is also an available option allowing simpler and more cost-effective system connectivity, with just a single CAT5 cable to carry multiple inputs via network. For your sports facilities, Ashly’s got a winning solution!

Amplifier needs for Houses of Worship can vary significantly depending on size and type. Smaller churches or those with simple speech amplification will generally require lower power. Worship facilities with larger congregations and with choirs, solo vocalists, organs, worship bands, etc.. will obviously require larger speaker systems and therefore higher power. Ashy offers a wide range of power solutions that fit just about any size worship facility. From 2 & 4-channel, 75 or 150W per channel nX Series, capable of driving any combination low impedance and hi-Z (70V) speakers to allow typical PA speakers and/or smaller distributed speaker systems. Add networking and Protea DSP for control, speaker processing and monitoring. for larger needs, nX goes all the way 3,000W per channel @ 2 Ohms for driving larger speaker systems, line arrays and subs, with available speaker processing to allow X-over, equalization (including FFIR filters), delay, limiting and Feedback Suppression. For smaller to medium-size facilities, pema offers a “church-in-a-box” solution. u to 8 x 250W at 4 Ohms or 70V, with 8×8 matrix processing and mic-mixing and all the protea DSP tools to make your system sing. oh and for those “digitally-minded” churches, Ashly nX, ne and Pema Series amps are available with Dante, so all your gear can easily connect via network with just a CAT5 wire. Where lower cost, simple operation and brute-force power is needed (and for when your processing is a separate component), KLR amps will provide workhorse performance all the way down to 2 Ohms for driving larger speaker arrays and power-hungry subs, delivering from 1,000-2, 500W per channel.